1. PREPARATION OF PAPERS
1.1 General Appearance
The text must be in English. The submitted typeset scripts of each contribution must be in their final form and of good appearance because they will be printed directly without any editing. It is essential that the "camera-ready copies" be absolutely clean and unfolded. The copy should be evenly printed on a high quality (300 dots/inch or higher) laser printer. There should not be corrections made on the printed pages. Your paper must be printed actual size (exactly how it is to appear in the Journals) in two columns. The document you are reading is printed in the format that should be used in your paper.
1.2 Specifications
As part of the printing process your document will be photographed. To ensure that this can be done with one camera setting for all papers and to ensure uniformity of appearance for the Journals, your paper should conform to the following specifications. If your paper deviates significantly from these specifications, the printer may not be able to include your paper in the Journals.
1) On the first page, the distance from the top edge of the paper to the top of the first line of type (the title) should be 1.57 inches (4.0 cm).
2) On the second and subsequent pages, the distance from the top edge of the paper to the top of the first line of type should be 1.18 inches (3.0 cm).
3) The left and right margins should be 1.38 inches (3.5 cm). If you are using A4 paper, set the right margin to 0.79 inches (2.0 cm).
4) The width of each column should be 21.62 characters.
5) The distance between the two columns of text should be 2.13 characters.
6) The space of lines should be 112%.
7) The distance from the top edge of the paper to the bottom of the last line of type on the page should be no more than 10 inches (25.4 cm).
2. RECOMMENDED POINT SIZES
We recommend a font of 9 points. The main text of this document is set in 9 point Times New Roman. If absolutely necessary, we suggest the use of condensed line spacing rather than smaller point sizes. Some technical formatting software prints mathematical formulas in italic type, with subscripts and superscripts in a slightly smaller font size. This is acceptable.
3. HEADINGS
Major headings are to be column centered in a bold font and in capitals without underline. They may be numbered, if so desired. "3. HEADINGS" at the top of this paragraph is a major heading.
3.1 Subheadings
Subheadings should be in a bold font and in lower case with initial capitals. They should start at the left-hand margin on a separate line.
3.1.1 Sub-subheadings: Sub-subheadings are to be in a bold font. They should be indented with two characters and run in at the beginning of the paragraph. The top of this paragraph illustrates a sub-subheading.
3.1.2 Title: The title should be centered across the top of the first page and should use 14 point type. It should be in a bold font and in lower case with initial capitals.
3.1.3 Authors’ Names and Addresses: The authors’ names and addresses should be centered below the title. These lines should be in at least 11 point type, but the particular point sizes and fonts are not critical and are left to the discretion of the authors.
3.1.4 Keywords: From 5 to 7 keywords should follow the abstract (as a subheading of the Abstract).
3.1.5 Illustrations or pictures: All illustrations should be original drawings or photographic prints of originals. Photographs should be glossy prints. Photocopies are often not good enough and should be avoided. All illustrations must be numbered consecutively (i.e., not section-wise). Center the figure captions beneath the figure. If possible, do not assemble figures at the back of your article, but place them as close as possible to where they are mentioned in the main text. Figures can span the two columns if need be (for those who use two-column format.)
4. FORMULAE
All equations must be typed or written neatly in black. They should be numbered consecutively throughout the text. Equation numbers should be enclosed in parentheses and flushed right. Equations should be referred to as Eq. (X) in the text where X is the equation number. In multiple-line equations, the number should be given on the last line.
5. TABLES
All tables must be numbered consecutively. Table headings should be placed above the table. Tables should be as close as possible to where they are mentioned in the main text. Tables can span the two columns if need be (for those who use two-column format.)
6. FOOTNOTES
Should be typed in singled-line spacing at the bottom of the page and column where it is cited. Footnotes should be rare.
7. FINALIZATION
Number your pages lightly, using a soft pencil, at the upper right-hand corners in the back of them (for example, 1/6, 2/6 and so forth). Please do NOT write on the fronts of the pages, or on the lower halves of the backs of the pages.
REFERENCES
List and number all bibliographical references at the end of your paper. When referenced in the text, enclose the citation number in square brackets, for example [1]. Where appropriate, include the name(s) of editors of referenced books. The following is an example of the recommended style for references.
[1] C.W. Churchman, The Design of Inquiring Systems, New York: Basic Books Inc. Pub., 1971.
[2] J. Ivari, "A Paradigmatic Analysis of Contemporary Schools of IS Development", European Journal of Information Systems, Vol. 1, No. 4, 1991, pp. 249-272.
Photograph
3X2.5(cm)
Author’s Name
He received the B.S., M.S in computer science from Daihan university, Korea in 1980, 1983 respectively and also received M.S., Ph.D. in electrical engineering from Rice university, USA in 1987. Since then, he has been with the Intelligent Control Center, Korea Institute of Science. His main research interests include microprocessor applications and high-performance drives.